Serial console
It is needed to open up the tablet and solder all four pins to PCB pads to get 1.8V LVCMOS output, baud rate is 115200 bps.
You can use Prolific PL-2303 RS232/USB converter, this one is from mobile phone flash cable.
To display the output use screen or minicom tool.
Example of output for ONN OPad N2
Init OK OUT [main]: BUILD[0006]=====2 [main]: enable mmu sc=0x2f [main]: do FTLInit... 183 [main]: OK! [main]: FltInit ===== 840 [main]: Current flash timing: 200000 [get_bootloader_ver]: BLOCK 0 [main]: Bootloader version: 2010-11-09#5.01 [main]: get parameter [main]: analyze parameter [ParseLine]: FW_VERSION: 1.0.1 [ParseLine]: ORG CMDLINE: noinitrd console=ttyS1,115200n8n init=/init root=/dev/mtdblock2 mem=208M@0x60000000 mtdparts=rk28xxnand:0x00002000@0x00002000(misc),0x00004000@0x00004000(kernel),0x00002000@0x00008000(boot), 0x00004000@0x0000A000(recovery),0x00040000@0x0000E000(system),0x0003A000@0x0004E000(backup), 0x0003A000@0x00088000(cache),0x00080000@0x000C2000(userdata),-@0x00142000(user) [main]: get command in misc [main]: no command [main]: Normal boot [check_cramfs]: Check boot partition... [check_cramfs]: Check ok! [load_kernel]: Kernel loading... [kernel_load_check]: Check kernel image... [kernel_load_check]: Check OK! [load_kernel]: Kernel load ok! [start_linux]: END ===== 13424 [start_linux]: CMDLINE: noinitrd console=ttyS1,115200n8n init=/init root=/dev/mtdblock2 mem=208M@0x60000000 mtdparts=rk28xxnand:0x00002000@0x00002000(misc),0x00004000@0x00004000(kernel),0x00002000@0x00008000(boot), 0x00004000@0x0000A000(recovery),0x00040000@0x0000E000(system),0x0003A000@0x0004E000(backup), 0x0003A000@0x00088000(cache),0x00080000@0x000C2000(userdata),-@0x00142000(user) bootver=2010-11-09#5.01 firmware_ver=1.0.1 [bootm_linux]: Starting kernel... [0] Linux version 2.6.25 (root@zuominggang) (gcc version 4.4.0 (GCC) ) #91 Tue Dec 14 13:38:38 PST 2010 [0] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 [0] Machine: RK28board [0] Memory policy: ECC disabled, Data cache writeback [0] On node 0 totalpages: 53248 [0] DMA zone: 416 pages used for memmap [0] DMA zone: 0 pages reserved [0] DMA zone: 52832 pages, LIFO batch:15 [0] Normal zone: 0 pages used for memmap [0] Movable zone: 0 pages used for memmap [0] CPU0: D VIVT write-back cache [0] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [0] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [0] CPU: found DTCM 16k @ 00000000, not enabled [0] CPU: DTCM was detected 16k but expected 4k! [0] CPU DTCM: copied data from ff404000 - ff404078 [0] CPU: found ITCM 8k @ 00000000, enabled [0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 52832 [0] PID hash table entries: 1024 (order: 10, 4096 bytes) [0] Console: colour dummy device 80x30 [0] console [ttyS1] enabled [0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [0] Memory: 208MB = 208MB total [0] Memory: 204544KB available (3976K code, 1934K data, 508K init) [0] Calibrating delay loop... 68.40 BogoMIPS (lpj=342016,armclk=137000000) [0] Mount-cache hash table entries: 512 [0] CPU: Testing write buffer coherency: ok [0] net_namespace: 152 bytes [0] CPU ITCM: Added 00000f10 bytes @ ff4010f0 to the TCM memory pool [0] NET: Registered protocol family 16 [0] PLLGetDDRFreq=136 MHZ [0] [0] ____________rk28_jogball_device___________ [0] =======RK2818 SCU VERSION=20111204,V1.10======= [0] [0] [0] [0] __rockchip_scu_tree_init:312000000 [0] [0] [0] [0] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=300000000 Hz [0] rockchip_clk_set_codecdsp::set dsp to 594000000 Hz,cur clk=24000000 Hz [0] Calibrating delay loop... 155.64 BogoMIPS (lpj=778240,armclk=312000000) [0] drivers/video/display/screen/lcd_hw_Td043mgea1.c [0] set iomux [0] -----------------lcdc freq = 37------------ [0] Console: switching to colour frame buffer device 100x30 k==0 [0] rk2818fb_probe ok [0] SCSI subsystem initialized [0] usbcore: registered new interface driver usbfs [0] usbcore: registered new interface driver hub [0] usbcore: registered new device driver usb [0] input: rk28_AD_button as /devices/platform/rk28_AD_button/input/input0 [0] rk28_dsp_mod_init dsp version v306_8 [0] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=594000000 Hz [1] SCU/W>dsp clk locked!! [1] NET: Registered protocol family 2 [1] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [1] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [1] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [1] TCP: Hash tables configured (established 8192 bind 8192) [1] TCP reno registered [1] ashmem: initialized [1] io scheduler noop registered [1] io scheduler anticipatory registered (default) [1] rockchip_usart.0: ttyS0 at MMIO 0x18000000 (irq = 19) is a ROCKCHIP_SERIAL [1] rockchip_usart.1: ttyS1 at MMIO 0x18002000 (irq = 20) is a ROCKCHIP_SERIAL [1] brd: module loaded [1] loop: module loaded [1] nbd: registered device at major 43 [1] PPP generic driver version 2.4.2 [1] PPP Deflate Compression module registered [1] PPP MPPE Compression module registered [1] NET: Registered protocol family 24 [1] PPPoL2TP kernel driver, V1.0 [1] usbcore: registered new interface driver asix [1] usbcore: registered new interface driver cdc_ether [1] usbcore: registered new interface driver dm9620 [1] usbcore: registered new interface driver net1080 [1] usbcore: registered new interface driver cdc_subset [1] usbcore: registered new interface driver zaurus [1] Linux video capture interface: v2.00 [1] [1] rk28_camera_probe..drivers/media/video/rk28_camera.c..843 ******** nzy ********* [1] [1] soc_camera_init..drivers/media/video/soc_camera.c..1148 ******** nzy ********* [1] [1] soc_camera_init..drivers/media/video/soc_camera.c..1156 ******** nzy ********* [1] Driver 'sd' needs updating - please use bus_type methods [1] Driver 'sr' needs updating - please use bus_type methods [1] Flash 0 ID: ad d7 94 9a 74 [1] Flash 1 ID: 0 0 0 0 0 [1] Flash 2 ID: 0 0 0 0 0 [1] Flash 3 ID: 0 0 0 0 0 [1] AccessTime: 40 ns [1] Flash timming: 10c3 [12] FTL INFO:Version = 420,Date = 2010118 [12] totalLogicBlkRaw = 1904 [12] max page blk = 256 [12] 9 cmdlinepart partitions found on MTD device rk28xxnand [12] Creating 9 MTD partitions on "rk28xxnand": [12] 0x00002000-0x00004000 : "misc" [12] 0x00004000-0x00008000 : "kernel" [12] 0x00008000-0x0000a000 : "boot" [12] 0x0000a000-0x0000e000 : "recovery" [12] 0x0000e000-0x0004e000 : "system" [12] 0x0004e000-0x00088000 : "backup" [12] 0x00088000-0x000c2000 : "cache" [12] 0x000c2000-0x00142000 : "userdata" [12] 0x00142000-0x00670000 : "user" [12] Creating 2 MTD partitions on "rk28xxnand": [12] 0x00000000-0x00030000 : "pagecache" [12] 0x00030000-0x00040000 : "swap" [12] >>> part[0]: name=misc offset=0x2000 [12] >>> part[1]: name=kernel offset=0x4000 [12] >>> part[2]: name=boot offset=0x8000 [12] >>> part[3]: name=recovery offset=0xA000 [12] >>> part[4]: name=system offset=0xE000 [12] >>> part[5]: name=backup offset=0x4E000 [12] >>> part[6]: name=cache offset=0x88000 [12] >>> SysImageWriteEndAdd=0x88000 [12] FtlSetSysProtAddr gFlashInfo.sysInfo.sysProtAddr = 151 [12] rockchip_spi_master rockchip_spi_master: rockchip SPI Master Controller at 0x1800e000 (irq 14) [12] spi spi0.0: setting pre-scaler to 780 (hz 100000) [12] usbcore: registered new interface driver cdc_acm [12] drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters [12] Initializing USB Mass Storage driver... [12] usbcore: registered new interface driver usb-storage [12] USB Mass Storage support registered. [12] usbcore: registered new interface driver usbserial [12] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic [12] usbcore: registered new interface driver usbserial_generic [12] drivers/usb/serial/usb-serial.c: USB Serial Driver core [12] drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port) [12] usbcore: registered new interface driver option [12] drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1 [12] dwc_otg_driver_probe,everest [12] DWC_otg: ^^^^^^^^^^^^^^^^^Device Mode 20100827 [12] dwc_otg_hcd_init everest [12] dwc_otg dwc_otg: DWC OTG Controller [12] dwc_otg dwc_otg: new USB bus registered, assigned bus number 1 [12] dwc_otg dwc_otg: irq 8, io mem 0x00000000 [12] DWC_otg: dwc_otg_hcd_start! everest [12] dwc_otg_hcd_start controller in device mode,everest [12] usb usb1: configuration #1 chosen from 1 choice [12] hub 1-0:1.0: USB hub found [12] hub 1-0:1.0: 1 port detected [13] DWC_otg: dwc_otg_hcd_init end,everest [13] dwc_otg_pcd_init,everest [13] dwc_otg_driver_probe end, everest [13] android init [13] android_probe pdata: c047047c [13] android_bind [13] mass_storage_function_add [13] android_usb gadget: Number of LUNs=2 [13] adb_function_add [13] android_usb gadget: android_usb ready [13] mice: PS/2 mouse device common for all mice [13] [13] xpt2046_ts_proble,0x90 [13] input: xpt2046 touchscreen as /devices/platform/rockchip_spi_master/spi0.0/input/input1 [13] ( 50, 40) => ( 49, 40) [13] maxErr=1 [13] ( 750, 40) => ( 750, 40) [13] maxErr=1 [13] ( 50, 440) => ( 50, 440) [13] maxErr=1 [13] ( 750, 440) => ( 750, 440) [13] maxErr=1 [13] v_CalcParam.a1=-19981 [13] v_CalcParam.b1=115 [13] v_CalcParam.c1= 78575450 [13] v_CalcParam.a2 = -70 [13] v_CalcParam.b2 = -12598 [13] v_CalcParam.c2 = 48247836 [13] v_CalcParam.delta = 95382 [13] Auto set calibration successfully. [13] MMA7660A compass driver: init [13] i2c /dev entries driver [13] [13] ov9650_probe..drivers/media/video/ov9650.c..743 ******** nzy ********* [13] [13] soc_camera_probe..drivers/media/video/soc_camera.c..861 ******** nzy ********* [13] camera 33-0: RK28 Camera driver attached to camera 0 [13] [13] ov9650_init..drivers/media/video/ov9650.c..340 ******** nzy *********0xff [13] camera 33-0: RK28 Camera driver detached from camera 0 [13] [13] soc_camera_probe..drivers/media/video/soc_camera.c..883 ******** nzy ********* [13] [13] ov9650_probe..drivers/media/video/ov9650.c..785 ******** nzy ********* [13] input: compass as /devices/virtual/input/input2 [13] aaa_I2CSendData[421]---error in _I2CSendData:I2C_ARBITR_LOSE_STATUS [13] _I2CWrite[954]--write data error! [14] rock28_i2c_transfer[1093] ERROR :write date in rock28 i2c,ret=-7,date=2 [14] _I2CSendData[421]---error in _I2CSendData:I2C_ARBITR_LOSE_STATUS [14] _I2CRead[720]--DIRECTMODE/TS8205MODE-send slave address ! [14] rock28_i2c_transfer[1073] ERROR :read date in rock28 i2c,ret=-9,date=0 [14] at18 check ok [14] rtc_HYM8563 0-0051: rtc core: registered rtc_HYM8563 as rtc0 [14] hym8563_init_device--->133 RTC_CTL2 = 40 [14] hym8563_init_device--->142 RTC_CTL2 = 40 [14] ---read time ------ year:2011, mon:1, day:20, weekday:4 hour:9 min:27 sec:42 [14] ------------>axp173 Debug:pmu_axp173_init::======================= [14] ------------>axp173 Debug:pmu_axp173_probe::============= [14] ------------>axp173 Debug:axp173_init_success!! [14] AccessTime: 40 ns [14] Flash timming: 10a2 [14] rockchip_battery_init::======================================== [14] rk28_sdmmc0_set_ios..drivers/mmc/host/rk28_sdmmc0.c..143 ***********The clock div is setted. the ios->clock=350 Khz******====xbw===****** [14] RK28 MMC SDIO HOST driver init ...... [14] Free DMA channel for SDMMC1. [14] usbcore: registered new interface driver usbhid [14] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [14] ********soft disconnect***************************************** [14] rk28_sdmmc0_set_ios..drivers/mmc/host/rk28_sdmmc0.c..143 ***********The clock div is setted. the ios->clock=49000 Khz******====xbw===****** [14] mmc0: host does not support reading read-only switch. assuming write-enable. [14] mmc_attach_sd..drivers/mmc/core/sd.c..925 - Now, call mmc_add_card to add a new card. [14] mmc0: new high speed SDHC card at address 1234 [14] logger: created 64K log 'log_main' [14] logger: created 4K log 'log_events' [14] logger: created 64K log 'log_radio' [14] pmem_setup::pmem pmem 1 init [14] pmem_setup::pmem pmem-dsp 0 init [14] mmc_blk_probe..drivers/mmc/card/block.c..609 ****begin to call add_disk() for a disk***xbw******* [14] mmcblk0:Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31 16:40:16 2008 UTC). [14] p1 [14] [14] mmc_rescan..777£º The card's type is SD. initialize successfully*********xbw******** [14] Request DMA channel for SDMMC1. [14] USB SUSPEND [14] ********soft connect!!!***************************************** [14] ASoC version 0.13.2 [14] USB SUSPEND [14] asoc: WM8988 <-> rockchip-i2s mapping ok [14] DWC_otg: USB RESET [15] CMD: 5 FAIL raw_ints: 104 masked ints: 4 [15] CMD: 5 FAIL raw_ints: 104 masked ints: 4 [15] CMD: 5 FAIL raw_ints: 104 masked ints: 4 [15] CMD: 5 FAIL raw_ints: 104 masked ints: 4 [15] Free DMA channel for SDMMC1. [15] ALSA device list: [15] #0: ROCKCHIP_WM8988 (WM8988) [15] TCP cubic registered [15] NET: Registered protocol family 1 [15] NET: Registered protocol family 17 [15] RPC: Registered udp transport module. [15] RPC: Registered tcp transport module. [15] ieee80211: 802.11 data/management/control stack, git-1.1.13 [15] ieee80211: Copyright (C) 2004-2005 Intel Corporation [15] input: jogball as /devices/platform/rk28_jogball/input/input3 [15] DWC_otg: USB RESET [15] ---read time ------ year:2011, mon:1, day:20, weekday:4 hour:9 min:27 sec:43 [15] rtc_HYM8563 0-0051: setting system clock to 2011-01-20 09:27:43 UTC (1295515663) [15] addr_console_init addr_console version v306_8 [15] ......__rockchip_ddr_frq_init [15] rockchip_clk_set_codecdsp::set codec to 140000000 Hz,cur clk=136000000 Hz [15] ......__rockchip_ddr_frq_init [15] rockchip_clk_set_codecdsp::set codec to 280000000 Hz,cur clk=140000000 Hz [15] ......__rockchip_ddr_frq_init [15] VFS: Mounted root (cramfs filesystem) readonly. [15] Freeing init memory: 508K [15] Warning: unable to open an initial console. [15] before start /init,now=0x389ad1fb2 [15] android_usb gadget: high speed config #1: android [15] set usb_msc_connect status = 1 20100803 [15] init: cannot open '/initlogo.rle' [15] init: ext_check(/dev/block/mtdblock7): [15] init: superblock offset = 0 [15] init: ext2fs_open2 retval = 0 [15] init: /dev/block/mtdblock7: recovering journal [21] init: superblock offset = 0 [21] init: ext2fs_open2 retval = 0 [21] init: /dev/block/mtdblock7: clean, 143/65536 files, 51464/262144 blocks [22] init: /system/bin/e2fsck terminated by exit(0) [22] init: filesystem '/dev/block/mtdblock7' had no errors [22] kjournald starting. Commit interval 5 seconds [22] EXT3 FS on mtdblock7, internal journal [22] EXT3-fs: mounted filesystem with ordered data mode. [22] init: ext_check(/dev/block/mtdblock6): [22] init: superblock offset = 0 [22] init: ext2fs_open2 retval = 0 [22] init: /dev/block/mtdblock6: recovering journal [22] init: superblock offset = 0 [22] init: ext2fs_open2 retval = 0 [22] init: /dev/block/mtdblock6: clean, 11/29760 files, 9427/118784 blocks [22] init: /system/bin/e2fsck terminated by exit(0) [22] init: filesystem '/dev/block/mtdblock6' had no errors [22] kjournald starting. Commit interval 5 seconds [22] EXT3 FS on mtdblock6, internal journal [22] EXT3-fs: mounted filesystem with ordered data mode. [22] init: ext_check(/dev/block/mtdblock9): [22] init: superblock offset = 0 [22] init: ext2fs_open2 retval = 0 [22] init: /dev/block/mtdblock9: recovering journal [27] init: superblock offset = 0 [27] init: ext2fs_open2 retval = 0 [27] init: /dev/block/mtdblock9: clean, 293/24576 files, 11033/98304 blocks [27] init: /system/bin/e2fsck terminated by exit(0) [27] init: filesystem '/dev/block/mtdblock9' had no errors [27] kjournald starting. Commit interval 5 seconds [27] EXT3 FS on mtdblock9, internal journal [27] EXT3-fs: mounted filesystem with ordered data mode. [27] init: cannot find '/init.sh', disabling 'init_sh' [27] init: cannot find '/system/bin/playmp3', disabling 'bootsound' [27] init: cannot find '/system/bin/flash_image', disabling 'flash_recovery' [27] warning: `adbd' uses 32-bit capabilities (legacy support in use) [27] enabling adb [28] Adding 32760k swap on /dev/block/mtdblock10. Priority:-1 extents:1 across:32760k sh: can't access tty; job control turned off # [46] rockchip_clk_set_codecdsp::set dsp to 594000000 Hz,cur clk=594000000 Hz [46] init: untracked pid 773 exited [46] init: untracked pid 776 exited [55] ================================== [55] I'm launching 88W8686 SDIO driver! [55] ================================== [55] MV8686 WiFi driver (Powered by Rockchip,Ver 2.12) init. [55] Request DMA channel for SDMMC1. [55] mmc1: new SDIO card at address 0001 [55] init: untracked pid 807 exited [55] init: untracked pid 810 exited [55] Data size = 124244 bytes, Time = 0.084 seconds, Rate = 11832 kbps [55] mv8686: ccc81d08M, fw 9.70.7p0, cap 0x00000303 region 0x10 [55] mv8686: wlan0: Marvell WLAN 802.11 adapter [64] sdmmc_reset_store------mmc receive the message of RemoveDone ----- [64] sdmmc_reset_store------mmc receive the message of RemoveDone ----- [69] binder: release 913:913 transaction 2576 out, still active [69] binder: 752:756 transaction failed 29189, size 4-0 [69] binder: send failed reply for transaction 2576, target dead [71] SN=0 uncali_x=342 uncali_y=3657 [71] SN=1 uncali_x=3721 uncali_y=3629 [71] SN=2 uncali_x=322 uncali_y=661 [71] SN=3 uncali_x=3745 uncali_y=557 [71] SN=4 uncali_x=2001 uncali_y=2092 [71] [71] xpt2046_callinit,0x90 [71] ( 50, 40) => ( 52, 43) [71] maxErr=3 [71] ( 750, 40) => ( 748, 38) [71] maxErr=3 [71] ( 50, 440) => ( 48, 438) [71] maxErr=3 [71] ( 750, 440) => ( 752, 442) [71] maxErr=3 [71] v_CalcParam.a1=20412 [71] v_CalcParam.b1=15 [71] v_CalcParam.c1= -1800008 [71] v_CalcParam.a2 = -255 [71] v_CalcParam.b2 = -13074 [71] v_CalcParam.c2 = 52164908 [71] v_CalcParam.delta = 99178 [107] SCU/W>armclk clk locked!! [121] SCU/W>armclk clk locked!! [121] SCU/W>armclk clk locked!! [133] SCU/W>armclk clk locked!! [137] SCU/W>armclk clk locked!! [292] SCU/W>armclk clk locked!! [339] SCU/W>armclk clk locked!! [351] SCU/W>armclk clk locked!! [353] SCU/W>armclk clk locked!! [363] SCU/W>armclk clk locked!! [438] SCU/W>armclk clk locked!! [726] ps_timer_function. [726] lbs_ps_worker [726] System want WIFI to suspend. [743] Need to wakeup for xmit: ether_proto=8. [743] lbs_ps_worker [743] System want WIFI to resume. [743] DEEP SLEEP AWAKE: Wakeup the caller. [961] ps_timer_function. [961] lbs_ps_worker [961] System want WIFI to suspend. [989] request_state_store gPoweroffFlag=1 [998] WM8988 shutdown.......... [998] dsp_drv_shutdown:: shutdown dsp [998] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=594000000 Hz [998] SCU/W>dsp clk locked!! [998] dwc_otg_driver_shutdown:: disconnect USB [998] rk2818fb_shutdown:: shutdown lcdc [998] Power down. [998] arch/arm/kernel/process.c...machine_power_off...240
Output for CyanogenMod 7 (Android 2.3.3)
Init OK
OUT
[main]: BUILD[0006]=====2
[main]: enable mmu
sc=0x2f
[main]: do FTLInit... 183
[main]: OK!
[main]: FltInit ===== 853
[main]: Current flash timing: 200000
[get_bootloader_ver]: BLOCK 0
[main]: Bootloader version: 2010-11-09#5.01
[main]: get parameter
[main]: analyze parameter
[ParseLine]: FW_VERSION: 1.0.1
[ParseLine]: ORG CMDLINE: noinitrd console=ttyS1,115200n8n init=/init root=/dev)
[main]: get command in misc
[main]: no command
[main]: Normal boot
[check_cramfs]: Check boot partition...
[check_cramfs]: Check ok!
[load_kernel]: Kernel loading...
[kernel_load_check]: Check kernel image...
[kernel_load_check]: Check OK!
[load_kernel]: Kernel load ok!
[start_linux]: END ===== 13898
[start_linux]: CMDLINE: noinitrd console=ttyS1,115200n8n init=/init root=/dev/m1
[bootm_linux]: Starting kernel...
[0] Linux version 2.6.25 (root@zuomg) (gcc version 4.4.0 (GCC) ) #31 Mon Dec 6 0
[0] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
[0] Machine: RK28board
[0] Memory policy: ECC disabled, Data cache writeback
[0] On node 0 totalpages: 53248
[0] DMA zone: 416 pages used for memmap
[0] DMA zone: 0 pages reserved
[0] DMA zone: 52832 pages, LIFO batch:15
[0] Normal zone: 0 pages used for memmap
[0] Movable zone: 0 pages used for memmap
[0] CPU0: D VIVT write-back cache
[0] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[0] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[0] CPU: found DTCM 16k @ 00000000, not enabled
[0] CPU: DTCM was detected 16k but expected 4k!
[0] CPU DTCM: copied data from ff404000 - ff404078
[0] CPU: found ITCM 8k @ 00000000, enabled
[0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 52832
[0] PID hash table entries: 1024 (order: 10, 4096 bytes)
[0] Console: colour dummy device 80x30
[0] console [ttyS1] enabled
[0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[0] Memory: 208MB = 208MB total
[0] Memory: 204800KB available (3972K code, 1745K data, 508K init)
[0] Calibrating delay loop... 68.40 BogoMIPS (lpj=342016,armclk=137000000)
[0] Mount-cache hash table entries: 512
[0] CPU: Testing write buffer coherency: ok
[0] net_namespace: 152 bytes
[0] CPU ITCM: Added 00000f10 bytes @ ff4010f0 to the TCM memory pool
[0] NET: Registered protocol family 16
[0] PLLGetDDRFreq=136 MHZ
[0]
[0] ____________rk28_jogball_device___________
[0] =======RK2818 SCU VERSION=20101012,V1.09=======
[0]
[0]
[0]
[0] __rockchip_scu_tree_init:312000000
[0]
[0]
[0]
[0] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=300000000 Hz
[0] rockchip_clk_set_codecdsp::set dsp to 594000000 Hz,cur clk=24000000 Hz
[0] Calibrating delay loop... 155.64 BogoMIPS (lpj=778240,armclk=312000000)
[0] drivers/video/display/screen/lcd_hw_Td043mgea1.c
[0] set iomux
[0] -----------------lcdc freq = 37------------
[0] Console: switching to colour frame buffer device 100x30 k==0
[0] rk2818fb_probe ok
[0] SCSI subsystem initialized
[0] usbcore: registered new interface driver usbfs
[0] usbcore: registered new interface driver hub
[0] usbcore: registered new device driver usb
[0] input: rk28_AD_button as /devices/platform/rk28_AD_button/input/input0
[0] rk28_dsp_mod_init dsp version v306_8
[0] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=594000000 Hz
[0] SCU/W>dsp clk locked!!
[0] NET: Registered protocol family 2
[1] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[1] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[1] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[1] TCP: Hash tables configured (established 8192 bind 8192)
[1] TCP reno registered
[1] ashmem: initialized
[1] io scheduler noop registered
[1] io scheduler anticipatory registered (default)
[1] rockchip_usart.0: ttyS0 at MMIO 0x18000000 (irq = 19) is a ROCKCHIP_SERIAL
[1] rockchip_usart.1: ttyS1 at MMIO 0x18002000 (irq = 20) is a ROCKCHIP_SERIAL
[1] brd: module loaded
[1] loop: module loaded
[1] nbd: registered device at major 43
[1] PPP generic driver version 2.4.2
[1] PPP Deflate Compression module registered
[1] PPP MPPE Compression module registered
[1] NET: Registered protocol family 24
[1] PPPoL2TP kernel driver, V1.0
[1] usbcore: registered new interface driver asix
[1] usbcore: registered new interface driver cdc_ether
[1] usbcore: registered new interface driver dm9620
[1] usbcore: registered new interface driver net1080
[1] usbcore: registered new interface driver cdc_subset
[1] usbcore: registered new interface driver zaurus
[1] Linux video capture interface: v2.00
[1]
[1] rk28_camera_probe..drivers/media/video/rk28_camera.c..843 ******** nzy **
[1]
[1] soc_camera_init..drivers/media/video/soc_camera.c..1148 ******** nzy ****
[1]
[1] soc_camera_init..drivers/media/video/soc_camera.c..1156 ******** nzy ****
[1] Driver 'sd' needs updating - please use bus_type methods
[1] Driver 'sr' needs updating - please use bus_type methods
[1] Flash 0 ID: ad d7 94 9a 74
[1] Flash 1 ID: 0 0 0 0 0
[1] Flash 2 ID: 0 0 0 0 0
[1] Flash 3 ID: 0 0 0 0 0
[1] AccessTime: 40 ns
[1] Flash timming: c2
[11] FTL INFO:Version = 416,Date = 20100830
[11] totalLogicBlkRaw = 1904
[11] max page blk = 256
[11] 9 cmdlinepart partitions found on MTD device rk28xxnand
[11] Creating 9 MTD partitions on "rk28xxnand":
[11] 0x00002000-0x00004000 : "misc"
[11] 0x00004000-0x00008000 : "kernel"
[11] 0x00008000-0x0000a000 : "boot"
[11] 0x0000a000-0x0000e000 : "recovery"
[11] 0x0000e000-0x0004e000 : "system"
[11] 0x0004e000-0x00088000 : "backup"
[11] 0x00088000-0x000c2000 : "cache"
[11] 0x000c2000-0x00142000 : "userdata"
[11] 0x00142000-0x00670000 : "user"
[11] Creating 2 MTD partitions on "rk28xxnand":
[11] 0x00000000-0x00020000 : "pagecache"
[11] 0x00020000-0x00040000 : "swap"
[11] >>> part[0]: name=misc offset=0x2000
[11] >>> part[1]: name=kernel offset=0x4000
[11] >>> part[2]: name=boot offset=0x8000
[11] >>> part[3]: name=recovery offset=0xA000
[11] >>> part[4]: name=system offset=0xE000
[11] >>> part[5]: name=backup offset=0x4E000
[11] >>> part[6]: name=cache offset=0x88000
[11] >>> SysImageWriteEndAdd=0x88000
[11] FtlSetSysProtAddr gFlashInfo.sysInfo.sysProtAddr = 151
[11] rockchip_spi_master rockchip_spi_master: rockchip SPI Master Controller at)
[11] spi spi0.0: setting pre-scaler to 780 (hz 100000)
[11] usbcore: registered new interface driver cdc_acm
[11] drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for Us
[11] Initializing USB Mass Storage driver...
[11] usbcore: registered new interface driver usb-storage
[11] USB Mass Storage support registered.
[11] usbcore: registered new interface driver usbserial
[11] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
[11] usbcore: registered new interface driver usbserial_generic
[11] drivers/usb/serial/usb-serial.c: USB Serial Driver core
[11] drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM mod)
[11] usbcore: registered new interface driver option
[11] drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
[11] dwc_otg_driver_probe,everest
[11] DWC_otg: ^^^^^^^^^^^^^^^^^Device Mode 20100827
[11] dwc_otg_hcd_init everest
[11] dwc_otg dwc_otg: DWC OTG Controller
[11] dwc_otg dwc_otg: new USB bus registered, assigned bus number 1
[11] dwc_otg dwc_otg: irq 8, io mem 0x00000000
[11] DWC_otg: dwc_otg_hcd_start! everest
[11] dwc_otg_hcd_start controller in device mode,everest
[11] usb usb1: configuration #1 chosen from 1 choice
[11] hub 1-0:1.0: USB hub found
[11] hub 1-0:1.0: 1 port detected
[11] DWC_otg: dwc_otg_hcd_init end,everest
[11] dwc_otg_pcd_init,everest
[11] dwc_otg_driver_probe end, everest
[11] android init
[11] android_probe pdata: c046e47c
[11] android_bind
[11] mass_storage_function_add
[11] android_usb gadget: Number of LUNs=2
[11] adb_function_add
[11] android_usb gadget: android_usb ready
[11] mice: PS/2 mouse device common for all mice
[11]
[11] xpt2046_ts_proble,0x90
[11] input: xpt2046 touchscreen as /devices/platform/rockchip_spi_master/spi0.01
[12] ( 50, 40) => ( 49, 40)
[12] maxErr=1
[12] ( 750, 40) => ( 750, 40)
[12] maxErr=1
[12] ( 50, 440) => ( 50, 440)
[12] maxErr=1
[12] ( 750, 440) => ( 750, 440)
[12] maxErr=1
[12] v_CalcParam.a1=-19981
[12] v_CalcParam.b1=115
[12] v_CalcParam.c1= 78575450
[12] v_CalcParam.a2 = -70
[12] v_CalcParam.b2 = -12598
[12] v_CalcParam.c2 = 48247836
[12] v_CalcParam.delta = 95382
[12] Auto set calibration successfully.
[12] MMA7660A compass driver: init
[12] i2c /dev entries driver
[12]
[12] ov9650_probe..drivers/media/video/ov9650.c..743 ******** nzy *********
[12]
[12] soc_camera_probe..drivers/media/video/soc_camera.c..861 ******** nzy ***
[12] camera 33-0: RK28 Camera driver attached to camera 0
[12]
[12] ov9650_init..drivers/media/video/ov9650.c..340 ******** nzy *********0xf
[12] camera 33-0: RK28 Camera driver detached from camera 0
[12]
[12] soc_camera_probe..drivers/media/video/soc_camera.c..883 ******** nzy ***
[12]
[12] ov9650_probe..drivers/media/video/ov9650.c..785 ******** nzy *********
[12] input: compass as /devices/virtual/input/input2
[12] aaa_I2CSendData[421]---error in _I2CSendData:I2C_ARBITR_LOSE_STATUS
[12] _I2CWrite[888]---send slave 7 bit address start_bit !
[12] rock28_i2c_transfer[1093] ERROR :write date in rock28 i2c,ret=-3,date=2
[12] _I2CSendData[421]---error in _I2CSendData:I2C_ARBITR_LOSE_STATUS
[12] _I2CRead[720]--DIRECTMODE/TS8205MODE-send slave address !
[13] rock28_i2c_transfer[1073] ERROR :read date in rock28 i2c,ret=-9,date=0
[13] at18 check ok
[13] rtc_HYM8563 0-0051: rtc core: registered rtc_HYM8563 as rtc0
[13] hym8563_init_device--->133 RTC_CTL2 = 0
[13] hym8563_init_device--->142 RTC_CTL2 = 0
[13] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:36 se7
[13] ------------>axp173 Debug:pmu_axp173_init::=======================
[13] ------------>axp173 Debug:pmu_axp173_probe::=============
[13] ------------>axp173 Debug:axp173_init_success!!
[13] AccessTime: 40 ns
[13] Flash timming: c2
[13] rockchip_battery_init::========================================
[13] rk28_sdmmc0_set_ios..drivers/mmc/host/rk28_sdmmc0.c..143 ***********The cl*
[13] rk28_mci_send_command,errorflag=2,cmd=0,cmdr=80008100,ret=0x0
[13] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[13] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[13] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[13] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[13] rk28_mci_send_command,errorflag=6,cmd=1,cmdr=80002041,ret=0x0
[13] RK28 MMC SDIO HOST driver init ......
[13] Free DMA channel for SDMMC1.
[13] Request DMA channel for SDMMC1.
[13] CMD: 5 FAIL raw_ints: 104 masked ints: 4
[13] usbcore: registered new interface driver usbhid
[13] CMD: 5 FAIL raw_ints: 104 masked ints: 4
[13] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[13] CMD: 5 FAIL raw_ints: 104 masked ints: 4
[13] CMD: 5 FAIL raw_ints: 104 masked ints: 4
[13] Free DMA channel for SDMMC1.
[13] logger: created 64K log 'log_main'
[13] logger: created 4K log 'log_events'
[13] logger: created 4K log 'log_radio'
[13] pmem_setup::pmem pmem 1 init
[13] pmem_setup::pmem pmem-dsp 0 init
[13] Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31 16:.
[13] ASoC version 0.13.2
[13] asoc: WM8988 <-> rockchip-i2s mapping ok
[13] ALSA device list:
[13] #0: ROCKCHIP_WM8988 (WM8988)
[13] TCP cubic registered
[13] NET: Registered protocol family 1
[13] NET: Registered protocol family 17
[13] RPC: Registered udp transport module.
[13] RPC: Registered tcp transport module.
[13] ieee80211: 802.11 data/management/control stack, git-1.1.13
[13] ieee80211: Copyright (C) 2004-2005 Intel Corporation
[13] input: jogball as /devices/platform/rk28_jogball/input/input3
[13] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:36 se7
[13] rtc_HYM8563 0-0051: setting system clock to 2011-04-26 14:36:37 UTC (13038)
[13] addr_console_init addr_console version v306_8
[13] ......__rockchip_ddr_frq_init
[13] rockchip_clk_set_codecdsp::set codec to 140000000 Hz,cur clk=136000000 Hz
[13] ......__rockchip_ddr_frq_init
[13] rockchip_clk_set_codecdsp::set codec to 280000000 Hz,cur clk=140000000 Hz
[13] ......__rockchip_ddr_frq_init
[13] VFS: Mounted root (cramfs filesystem) readonly.
[13] Freeing init memory: 508K
[13] Warning: unable to open an initial console.
[13] before start /init,now=0x33b0587dd
[14] init: cannot open '/initlogo.rle'
[14] kjournald starting. Commit interval 5 seconds
[14] EXT3 FS on mtdblock7, internal journal
[14] EXT3-fs: recovery complete.
[14] EXT3-fs: mounted filesystem with ordered data mode.
[14] kjournald starting. Commit interval 5 seconds
[14] EXT3 FS on mtdblock6, internal journal
[14] EXT3-fs: recovery complete.
[14] EXT3-fs: mounted filesystem with ordered data mode.
sh: can't access tty; job control turned off
$ [15] enabling adb
[31] warning: `zygote' uses 32-bit capabilities (legacy support in use)
[32] rockchip_clk_set_codecdsp::set dsp to 594000000 Hz,cur clk=594000000 Hz
[66] SN=0 uncali_x=386 uncali_y=3530
[66] SN=1 uncali_x=3717 uncali_y=3565
[66] SN=2 uncali_x=364 uncali_y=604
[66] SN=3 uncali_x=3719 uncali_y=555
[66] SN=4 uncali_x=1980 uncali_y=1790
[66]
[66] xpt2046_callinit,0x90
[66] ( 50, 40) => ( 51, 43)
[66] maxErr=3
[66] ( 750, 40) => ( 749, 37)
[66] maxErr=3
[66] ( 50, 440) => ( 49, 437)
[66] maxErr=3
[66] ( 750, 440) => ( 751, 443)
[66] maxErr=3
[66] v_CalcParam.a1=19202
[66] v_CalcParam.b1=-64
[66] v_CalcParam.c1= -2437819
[66] v_CalcParam.a2 = -27
[66] v_CalcParam.b2 = -12357
[66] v_CalcParam.c2 = 47607706
[66] v_CalcParam.delta = 91706
[73] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=594000000 Hz
[73] SCU/W>dsp clk locked!!
[80] rockchip_clk_set_codecdsp::set dsp to 594000000 Hz,cur clk=594000000 Hz
[101] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=594000000 Hz
[101] SCU/W>dsp clk locked!!
[105] rockchip_clk_set_codecdsp::set dsp to 594000000 Hz,cur clk=594000000 Hz
[110] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=594000000 Hz
[110] SCU/W>dsp clk locked!!
[119] Gsensor mma7760 enter suspend
[119] rockchip_clk_set_codecdsp::set dsp to 594000000 Hz,cur clk=594000000 Hz
[119] scu_ddr_early_suspend:set arm clk from 594000000Hz
[119] AccessTime: 40 ns
[119] Flash timming: a2
[119] AccessTime: 40 ns
[119] Flash timming: a2
[119] to 148500000Hz
[119] scu_reduce_codec_pll::change ddr freq=140000000 HZ
[119] rockchip_clk_set_codecdsp::set codec to 140000000 Hz,cur clk=280000000 Hz
[119] rockchip_clk_set_codecdsp::set codec to 140000000 Hz,cur clk=140000000 Hz
[119] scu_reduce_codec_pll::change ddr freq=140 MHZ
[119] android_power_suspend: enter pm suspend
[119] PM: Syncing filesystems ... done.
[119] PM: Preparing system for mem sleep
[119] Freezing user space processes ... (elapsed 0.01 seconds) done.
[119] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
[119] PM: Entering mem sleep
[119] WiFi is disabled for now.
[119] alarm_suspend(alarm_enabled=11, alarm_pending=0)
[119] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:38 s3
[119] set alarm - rtc 12:38:42 04/27/2011 week=03
[119] >>hym8563_i2c_set_alarm->395---tm->enabled=1 tm->pending=1
[119]
[119] curent alarm register->rmin=27 rhour=12 rmday=27 rwday=3!
[119]
[119] ---hym8563_i2c_set_alarm-->rmin=38 rhour=12 rmday=27 rwday=3!
[119] >>hym8563_i2c_set_alarm->436---data==2
[119] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:38 s3
[119] Read rtc - rtc 14:38:23 04/26/2011 week=02
[119] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:38 s3
[119] dwc_otg_hcd_suspend, usb device mode
[119] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=594000000 Hz
[119] SCU/W>dsp clk locked!!
[119] AccessTime: 40 ns
[119] Flash timming: 61
[119] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=594000000 Hz
[119] before core halt,build[A7-20100916.01]
[135] AccessTime: 40 ns
[135] Flash timming: a2
[135] rockchip_clk_set_codecdsp::set dsp to 594000000 Hz,cur clk=24000000 Hz
[135] quit arm halt,irq_val=0x40
[127] dwc_otg_hcd_resume, usb device mode
[127] rk28_mci_send_command,errorflag=2,cmd=0,cmdr=80008100,ret=0x0
[127] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[127] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[127] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[127] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[127] rk28_mci_send_command,errorflag=6,cmd=1,cmdr=80002041,ret=0x0
[127] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:38 s0
[127] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:38 s0
[127] >>hym8563_i2c_read_alarm->383---read alarm and clean disable alarm
[128] Android want wifi to be resumed.
[128] PM: Finishing wakeup.
[128] Restarting tasks ... done.
[128] rockchip_clk_set_codecdsp::set codec to 140000000 Hz,cur clk=140000000 Hz
[128] rockchip_clk_set_codecdsp::set codec to 280000000 Hz,cur clk=140000000 Hz
[128] AccessTime: 40 ns
[128] Flash timming: a2
[128] AccessTime: 40 ns
[128] Flash timming: c3
[128] rockchip_clk_set_codecdsp::set dsp to 594000000 Hz,cur clk=594000000 Hz
[128]
[128] xpt2046_callinit,0x90
[128] Gsensor mma7760 resume!!
[133] Gsensor mma7760 enter suspend
[133] scu_ddr_early_suspend:set arm clk from 624000000Hz
[133] AccessTime: 40 ns
[133] Flash timming: a2
[133] AccessTime: 40 ns
[133] Flash timming: a2
[133] to 156000000Hz
[133] scu_reduce_codec_pll::change ddr freq=140000000 HZ
[133] rockchip_clk_set_codecdsp::set codec to 140000000 Hz,cur clk=280000000 Hz
[133] rockchip_clk_set_codecdsp::set codec to 140000000 Hz,cur clk=140000000 Hz
[133] scu_reduce_codec_pll::change ddr freq=140 MHZ
[133] android_power_suspend: enter pm suspend
[133] PM: Syncing filesystems ... done.
[133] PM: Preparing system for mem sleep
[133] Freezing user space processes ... (elapsed 0.01 seconds) done.
[133] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
[133] PM: Entering mem sleep
[133] WiFi is disabled for now.
[133] alarm_suspend(alarm_enabled=11, alarm_pending=0)
[133] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:38 s6
[133] set alarm - rtc 12:38:42 04/27/2011 week=03
[133] >>hym8563_i2c_set_alarm->395---tm->enabled=1 tm->pending=1
[133]
[133] curent alarm register->rmin=38 rhour=12 rmday=27 rwday=3!
[133]
[133] ---hym8563_i2c_set_alarm-->rmin=38 rhour=12 rmday=27 rwday=3!
[133] >>hym8563_i2c_set_alarm->436---data==2
[133] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:38 s6
[133] Read rtc - rtc 14:38:36 04/26/2011 week=02
[133] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:38 s6
[133] dwc_otg_hcd_suspend, usb device mode
[133] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=594000000 Hz
[133] SCU/W>dsp clk locked!!
[133] AccessTime: 40 ns
[133] Flash timming: 61
[133] rockchip_clk_set_codecdsp::set dsp to 24000000 Hz,cur clk=594000000 Hz
[133] before core halt,build[A7-20100916.01]
[139] AccessTime: 40 ns
[139] Flash timming: a2
[139] rockchip_clk_set_codecdsp::set dsp to 594000000 Hz,cur clk=24000000 Hz
[139] quit arm halt,irq_val=0x40
[136] dwc_otg_hcd_resume, usb device mode
[136] rk28_mci_send_command,errorflag=2,cmd=0,cmdr=80008100,ret=0x0
[136] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[136] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[136] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[136] rk28_mci_send_command,errorflag=6,cmd=55,cmdr=80002177,ret=0x0
[136] rk28_mci_send_command,errorflag=6,cmd=1,cmdr=80002041,ret=0x0
[136] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:38 s8
[137] ---read time ------ year:2011, mon:4, day:26, weekday:2 hour:14 min:38 s8
[137] >>hym8563_i2c_read_alarm->383---read alarm and clean disable alarm
[137] Android want wifi to be resumed.
[137] PM: Finishing wakeup.
[137] Restarting tasks ... done.
[137] rockchip_clk_set_codecdsp::set codec to 140000000 Hz,cur clk=140000000 Hz
[137] rockchip_clk_set_codecdsp::set codec to 280000000 Hz,cur clk=140000000 Hz
[137] AccessTime: 40 ns
[137] Flash timming: a2
[137] AccessTime: 40 ns
[137] Flash timming: c3
[137] rockchip_clk_set_codecdsp::set dsp to 594000000 Hz,cur clk=594000000 Hz
[137]
[137] xpt2046_callinit,0x90
[137] Gsensor mma7760 resume!!